Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Roofing: The Houston Owner’s Guide
If you have a Barrette roof component that’s failed, here’s the straight answer: we match and install Barrette-compatible roofing parts across Houston, and most replacements run $400 – $1,800 installed depending on what failed and how much decking or flashing has to come up with it. We stock the common failure points on our trucks, so a lot of these jobs are one trip.
The way most Houston homeowners find us is the same story: a shingle or metal panel lifted after a March storm, water showed up on the ceiling a week later, or a ridge cap cracked enough that the attic started sweating. Barrette makes solid products, but Houston’s heat-and-humidity cycle works every seam, every fastener, every flashing joint. When one piece fails, it usually tells you something about the ones around it.
Which Barrette Models This Applies To
Barrette’s roofing line splits into a few families: the cedar-look shake panels, the standing-seam metal profiles, and the traditional asphalt shingle lines, plus the ridge caps and rake trims that finish each system. The challenge with Barrette is that the older shake profile locks differently than the newer one. A homeowner will sometimes order a replacement panel online, get it up on the ladder, and find the lock leg won’t seat because the profile changed in 2018. If you’re holding a piece in your hand, don’t guess. Look at the back edge. The older panels have a single locking flange; the newer ones have a double-step interlock. Send us a photo before you buy anything.
On the metal line, Barrette uses a 36-inch panel width with widths measured across the flat, not across the ribs. People measure across the ridges, order a 38-and-change panel, and nothing lines up. We handle OEM matching where Barrette still makes the part, and we’ll tell you plainly when a quality aftermarket equivalent is the better value. Barrette discontinued several colors and trim profiles over the years, and on those, OEM just isn’t available anymore. We are an independent Houston service provider, not affiliated with Barrette, so our only interest is getting you the right part at the right price, whether that’s OEM or a matched equivalent.
Styles & brands we work with
Signs Your Barrette Roofing Is Failing
- Stained or drooping underlayment in the attic. Water has already gotten past the roof surface. In Houston, where attic temperatures can hit 140 degrees in August, trapped moisture breaks down roof decking fast. If you see it, the leak has been active for weeks, not days.
- Curled or lifted panel edges along the south and west exposures. Those are the sides that take our heaviest sun. When the edges lift, the interlock releases, and the next good windstorm peels panels back like a tin opener.
- Rust streaks running down from fasteners on the metal profiles. The neoprene washer under the screw head has dried and cracked. Every one of those fasteners is now a slow leak waiting for a heavy rain.
- Missing or cracked ridge cap pieces after a wind event. The ridge is the highest point and catches wind pressure first. A cracked cap lets water run straight down into the structure, often without showing up on the ceiling until damage is already done.
- Granule loss showing through on the asphalt lines. If you sweep tan granules out of your gutters after every rain, the shingle surface is wearing out. Barrette’s shingle line, like all shingle lines in our climate, fights a constant UV assault. Once the granules go, the sun eats the asphalt base in two or three seasons.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Barrette-specific roof work in Houston, small repairs like a single panel swap or a ridge cap replacement run $400 – $900. A larger section, like eight or ten shake panels with underlayment replacement and refastening a roof face, lands in the $1,200 – $1,800 range. Full roof replacements start at $8,000 and climb to $20,000 depending on square footage, pitch, and how many layers of old material have to come off first.
Every one of those numbers includes the part, the labor, the fasteners, the sealant, and the disposal. What moves the price is condition: if your decking (the wood layer under the roof surface) has gone soft from a slow leak, that’s an additional line item and we’ll say so before the first screw comes out. You get a written price before work starts, and you get our 365-Day Done Right Promise in writing with the job. If the repair fails inside that window, we come back and fix it at no charge. No service call fee, no re-inspection fee.
DIY or Call Us?
The honest split is this: you can safely check your attic for stains, walk the perimeter and look for lifted edges with binoculars from the ground, and clean your gutters. What you shouldn’t do is get on a Houston roof in July when the surface temperature is 150 degrees, try to reseat a panel you can’t identify, or work on a steep pitch without the right fall protection. Roof work is one of the places where a wrong step costs more than any repair ever would.
Even if you’re handy, the problem with Barrette parts is matching them. Get it wrong and you’ve spent $300 on a panel that doesn’t interlock or a cap that’s the wrong radius. Call us at (254) 527-5340. We’ll tell you over the phone whether it sounds like a one-piece fix or something bigger, and give you a written number before any work starts.
FAQs
Barrette’s metal and shake profiles should give you 25 to 40 years in the Houston climate, but the asphalt shingle lines typically run 15 to 20 years here. Our heat and humidity shorten the asphalt lifespan more than any other factor. The fasteners and underlayment usually fail before the panels themselves do, which is why we check both on every repair. Call (254) 527-5340 if you want us to look at what’s wearing.
Sometimes, yes. A single cracked ridge cap or a lifted panel with an intact interlock can often be resecured rather than replaced. The decision comes down to whether the surrounding material is still sound. If we can save you money with a proper fix, we will, and we’ll write the price before touching a tool. Call (254) 527-5340 for an honest assessment.
Most single-panel or ridge cap replacements take two to three hours once we’re on site. The bigger variable is scheduling and weather. We give you a defined arrival window and we don’t start roof work when the forecast shows lightning, because nobody should be on a roof with a storm cell moving in. Call (254) 527-5340 and we’ll give you a straight answer on timing.
Yes, we stock the common failure points: ridge caps in neutral colors, replacement fasteners, underlayment, and the most-used shake panels. If your part is one of the discontinued profiles, we’ll source a matched equivalent and show you the difference before ordering. We also work with other trade brands like KraftMaid, Cambria, and Silestone for their part lines, but Barrette roofing is what we’re talking about today. Call (254) 527-5340 with a photo and the measurements, and we’ll tell you exactly what we can do.
Give me the straight story on what you need, and I’ll give you the straight number on what it costs. If you’re in Houston and your Barrette roof is failing, call (254) 527-5340 for a free estimate. A real person answers, we show up in the window we gave you, and the number we write is the number you pay.
Written by Trevor Nash, Owner, Penhallow Remodeling Houston at Penhallow Remodeling Houston, serving Houston and nearby areas.
